What causes hydrogen sulfide in a lift station?

Hydrogen sulfide (H2S) forms inside the wastewater itself, not in the air above it. Wastewater held too long in a force main, a wet well or the pipe leading into a lift station uses up its dissolved oxygen. Once that oxygen is gone, the bacteria that live in every wastewater stream turn to sulfate as an oxygen source instead, and the sulfide left behind becomes hydrogen sulfide gas the moment the water is disturbed. The cause is septicity, not a broken valve or a failed pump.

Key terms

  • H2S (hydrogen sulfide): a colorless, corrosive gas produced when bacteria in wastewater draw oxygen from sulfate instead of from dissolved oxygen in the water.
  • BOD (biochemical oxygen demand): a measure of how much oxygen bacteria need to break down the organic matter in a wastewater stream. A higher BOD load uses up dissolved oxygen faster.
  • ppm (parts per million): the unit a gas monitor or a lab report uses to state a concentration, whether of hydrogen sulfide in air or sulfide in water.
  • Detention time: how long wastewater sits in a pipe, a wet well or a lift station before it moves downstream. Longer detention time gives bacteria more time to exhaust the available oxygen.
  • Septicity: the condition of wastewater that has used up its dissolved oxygen, so sulfate-reducing bacteria dominate over the aerobic bacteria that need oxygen to work.
  • Confined space: an enclosed area with limited entry and exit, such as a wet well or a dry pit, where a dangerous atmosphere can develop and specific entry procedures apply.

Why does wastewater turn septic on the way to a lift station?

Every wastewater stream carries dissolved oxygen when it leaves the point of use, and every wastewater stream carries the bacteria that will consume it. A long force main run, low flow, warm weather and a high organic load all shorten how long that dissolved oxygen lasts. Once it is gone, sulfate-reducing bacteria take over. They strip oxygen from sulfate ions, present in ordinary wastewater, and the byproduct is dissolved sulfide. Dissolved sulfide is not yet a gas. It stays in solution until something disturbs it.

Where does the gas actually release?

Dissolved sulfide escapes into the air as hydrogen sulfide gas where the water loses pressure or gains turbulence, which is exactly what happens inside a lift station. A force main discharging into a wet well, a drop structure, a pump turning over or the flow hitting a downstream manhole all agitate water that has carried dissolved sulfide quietly for miles. That is why the smell and the readings concentrate at the wet well and the discharge manhole even though the cause started upstream, often at the far end of the collection system. An operator chasing the smell at the station is looking in the right place for the release and the wrong place for the cause.

How does hydrogen sulfide corrode a lift station?

Hydrogen sulfide gas rising off the water surface reacts with moisture on concrete and steel above the waterline, and bacteria living in that moisture film oxidize the gas into sulfuric acid. Sulfuric acid attacks concrete directly, eating away the crown of the pipe, the underside of a manhole lid and the walls of a wet well above the waterline, year after year. This is a slow, structural problem (see whether hydrogen sulfide corrodes pumps and equipment), separate from the safety hazard the same gas creates in the air, and it often stays invisible until a rehabilitation project turns up damage nobody scheduled for.

Why smell is not a safety reading

Hydrogen sulfide has a strong rotten-egg smell at low concentrations, which is exactly why it is dangerous to rely on smell as a warning. At higher concentrations the gas dulls the sense of smell, so a worker can lose the ability to detect it right at the concentration where detection matters most. A nose is not an instrument. It has no calibration and no memory of the reading from five minutes ago. A calibrated, bump-tested gas monitor reading in ppm is the only reliable way to know what concentration is actually present in a wet well or any confined space before anyone enters.

What do gas monitors and confined space rules require?

OSHA (the Occupational Safety and Health Administration) sets a ceiling limit for hydrogen sulfide exposure and requires confined space entry procedures, including atmospheric testing, ventilation and a trained attendant, for spaces like wet wells. Federal OSHA covers private employers directly; whether it covers a public utility’s own crew depends on the state, since only a state-run OSHA-approved plan extends the same protections to public employees, and not every state has one. NIOSH (the National Institute for Occupational Safety and Health) is a research agency, not an enforcement one; it publishes its own recommended exposure limits, generally lower than OSHA’s, that inform safety practice even where they are not themselves enforceable. State rural water associations run confined-space and gas-monitor training for small-system operators. None of this changes because a station is being treated for hydrogen sulfide. Monitors, ventilation and entry procedures apply at every station, treated or not.

How do the control options compare?

Option How it works What it addresses Where it falls short
Iron salts and other scavengers Iron reacts with dissolved sulfide in the water to form a solid, pulling it out of solution Sulfide already present in the wastewater Treats sulfide after the bacteria have already made it. Dosing has to keep pace with a changing load
Scrubbers and masking agents Strip hydrogen sulfide from the air, or cover the odor with another scent The smell and the gas concentration in the headspace above the water Do not touch the water where the sulfide is formed. A scrubber is capital equipment, and a masking agent leaves the underlying hazard unmeasured
Aeration Mechanical or diffused air raises dissolved oxygen wherever the blowers reach Oxygen at a plant or an aerated basin Water can hold only a limited amount of dissolved oxygen, and aeration cannot reach a force main, a wet well or a sludge blanket upstream of the blowers
Supplying usable oxygen upstream An inorganic compound carries oxygen to the bacteria already in the wastewater, as far upstream as water and power allow The sulfate reduction reaction itself, before sulfide is formed A biological program, not a fix for a mechanical problem such as an undersized wet well or a failed pump

Iron salts, scrubbers and masking agents all treat hydrogen sulfide after the water has already made it. Aeration works, but only where the equipment reaches, and water can only hold so much dissolved oxygen no matter how hard it is aerated. Supplying usable oxygen upstream is the one option on this list aimed at the sulfate reduction reaction itself, before there is sulfide to scavenge or scrub.

When a biological program fits, and when it does not

A program built around supplying usable oxygen upstream fits a station where septic wastewater is the real cause: dissolved oxygen has run out somewhere in the collection system, sulfide is forming, and the gas and the corrosion follow from it. It does not fix a station where the wet well is undersized for its flow, a check valve or a pump has failed, or the odor traces back to grease and debris rather than dissolved sulfide. Waste Water Innovations (WWI) runs a program built on this idea: we dose usable oxygen as far upstream as a site’s water and power allow, as a monthly service, with no chemical additives, no added bacteria and no added enzymes. How that applies specifically to a lift station, including where the dosing point goes and what a review looks for, is on the lift station H2S control page. A documented Texas site is in the lift station H2S case study.

Summary

  • Hydrogen sulfide forms in the wastewater when dissolved oxygen runs out and bacteria turn to sulfate instead, then releases as gas wherever the water turns turbulent, typically the wet well or a discharge manhole.
  • The gas is both a safety hazard, worse than smell alone can indicate, and a slow corrosion problem that eats away at concrete and steel above the waterline.
  • Control options range from treating the gas after it forms, with iron salts, scrubbers or masking agents, to reaching further upstream with oxygen so sulfide is not made in the first place. Gas monitors and confined space procedures apply regardless of which option a station uses.